| 國立成功大學 |
2021-03~2021-04 |
Effects of heat treatment on a novel continuous casting direct rolling 6056 aluminum alloy: cold rolling characteristics and tensile fracture properties
|
Zhao;Jun-Ren;Hung;Fei-Yi;Chen;Bo-Jou |
| 國立成功大學 |
2021-03 |
Novel photovoltaic ribbon technology: Interfacial behavior of In-50Sn alloy ribbon without metal matrix under electrothermal effects and chlorine corrosion
|
Chen;Kuan-Jen;Fang;Yu-Hui;Hung;Fei-Yi |
| 國立成功大學 |
2021-03 |
Optical, Microstructure, and Electromagnetic Properties of (1-x)ZnO - xCuO Powders Prepared Using Two-Stage Sintering and Direct Synthesis
|
Liu;Tai-Hsiang;Hung;Fei-Yi;Chen;Cheng-Hung;Chen;Kuan-Jen |
| 國立成功大學 |
2021-01 |
Microstructure, Mechanical Properties, and Fatigue Fracture Characteristics of High-Fracture-Resistance Selective Laser Melting Al-Ni-Cu Alloys
|
Chang;Kai-Chieh;Zhao;Jun-Ren;Hung;Fei-Yi |
| 國立成功大學 |
2020-11~2020-12 |
Interface behavior and electrical properties of Zn-Sn-Cu (CTZ) stacking layer films with thermal diffusion and electrically induced crystallization
|
Liu;Tai-Hsiang;Hung;Fei-Yi;Chen;Kuan-Jen |
| 國立成功大學 |
2020-11 |
Biodegradation ZK50 magnesium alloy compression screws: Mechanical properties, biodegradable characteristics and implant test
|
Chen;Yen-Ting;Hung;Fei-Yi;Lin;Yen-Ling;Lin;Chia-Yen |
| 國立成功大學 |
2020-07~2020-08 |
Improving the applicability of wear-resistant Al-10Si-0.5 Mg alloy obtained through selective laser melting with T6 treatment in high-temperature, and high-wear environments
|
Chen;Kuan-Jen;Hung;Fei-Yi;Lui;Truan-Sheng;Tsai;Chun-Lin |
| 國立成功大學 |
2020-06 |
Wedge bonding technologies: microstructure, mechanical properties and electrical properties of fine Al-Zn-Si alloy wire
|
Wu;Bo-Ding;Hung;Fei-Yi |
| 國立成功大學 |
2020-05~2020-06 |
Microstructure and tensile fracture behavior of three -stage heat treated inconel 718 alloy produced via laser powder bed fusion process
|
Zhao;Jun-Ren;Hung;Fei-Yi;Lui;Truan-Sheng |
| 國立成功大學 |
2020-03 |
Microstructure, optical, electrical, and magnetic properties of ZnO/CuO thin films prepared using two-stage magnetron sputtering and diffusion doping process
|
Liu;Tai-Hsiang;Hung;Fei-Yi;Chen;Cheng-Hung;Chen;Kuan-Jen |
| 國立成功大學 |
2020-03 |
A New Infrared Heat Treatment on Hot Forging 7075 Aluminum Alloy: Microstructure and Mechanical Properties
|
Chang;Yi-Ling;Hung;Fei-Yi;Lui;Truan-Sheng |
| 國立成功大學 |
2020-01 |
Opto-electromagnetic properties of carbon-doped zinc-oxide prepared using electrically induced crystallization and ion implantation process for gas sensor application
|
Liu;Tai-Hsiang;Hung;Fei-Yi;Chien;Tao;Chen;Kuan-Jen |
| 國立成功大學 |
2020-01 |
Erosion Resistance and Particle Erosion-Induced Tensile Embrittlement of 3D-Selective Laser Melting Inconel 718 Superalloy
|
Zhao;Jun-Ren;Hung;Fei-Yi;Lui;Truan-Sheng |
| 國立成功大學 |
2019-12 |
Study of electrical fatigue test in gold-coated siliver-4 wt.% palladium bonding wire
|
Ho;Chen-Chin;Chen;Kuan-Jen;Hung;Fei-Yi;Lui;Truan-Sheng |
| 國立成功大學 |
2019-08 |
Biodegradable Implantation Material: Mechanical Properties and Surface Corrosion Mechanism of Mg-1Ca-0.5Zr Alloy
|
Chen;Yen-Ting;Hung;Fei-Yi;Syu;Jie-Cheng |
| 國立成功大學 |
2019-08 |
Low Conductivity Decay of Sn-0.7Cu-0.2Zn Photovoltaic Ribbons for Solar Cell Application
|
Chen;Kuan-Jen;Hung;Fei-Yi;Lui;Truan-Sheng;Hsu;Lin |
| 國立成功大學 |
2019-07 |
A Study of the Sulfidation Behavior on Palladium-Coated Copper Wire with a Flash-Gold Layer (PCA) after Wire Bonding
|
Chen;Kuan-Jen;Hung;Fei-Yi;Chang;Chia-Yun |
| 國立成功大學 |
2019-07 |
Particle Erosion Induced Phase Transformation of Different Matrix Microstructures of Powder Bed Fusion Ti-6Al-4V Alloy Flakes
|
Zhao;Jun-Ren;Hung;Fei-Yi;Lui;Truan-Sheng |
| 國立成功大學 |
2019-05~2019-06 |
Impact of solid-solution treatment on microstructural characteristics and formability of rotary-swaged 2024 alloy tubes
|
Lin;Chia-Wei;Chen;Kuan-Jen;Hung;Fei-Yi;Lui;Truan-Sheng;Chen;Hsuan-Po |
| 國立成功大學 |
2019-05 |
The Relationship of Fracture Mechanism between High Temperature Tensile Mechanical Properties and Particle Erosion Resistance of Selective Laser Melting Ti-6Al-4V Alloy
|
Zhao;Jun-Ren;Hung;Fei-Yi;Lui;Truan-Sheng;Wu;Yu-Lin |
| 國立成功大學 |
2019-03-15 |
The effect of hyper-rotation on the Weibull distribution of tensile properties in a friction stirred AA7075 aluminum alloy
|
Ku;Ming-Hsiang;Hung;Fei-Yi;Lui;Truan-Sheng |
| 國立成功大學 |
2019-02 |
Examination of the High Tensile Ductility Improvement in an As-Solutionized AA7075 Alloy with the Aid of a Friction Stir Process
|
Ku;Ming-Hsiang;Hung;Fei-Yi;Lui;Truan-Sheng |
| 國立成功大學 |
2019-01~2019-03 |
Study of microstructure and tensile properties of infrared-heat-treated cast-forged 6082 aluminum alloy
|
Chang;Yi-Ling;Hung;Fei-Yi;Lui;Truan-Sheng |
| 國立成功大學 |
2019-01-2 |
Embrittlement Due to Excess Heat Input into Friction Stir Processed 7075 Alloy
|
Ku;Ming-Hsiang;Hung;Fei-Yi;Lui;Truan-Sheng |
| 國立成功大學 |
2019 |
Wear Inducing Phase Transformation of Plasma Transfer Arc Coated Tools during Friction Stir Welding with Al Alloy
|
Chen;Kuan-Jen;Hung;Fei-Yi;Lui;Truan-Sheng;Shih;Yong-Ren |
